Sign in perhaps register 。

　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.Monte Cristo San Fernando,　　Before distinguishing pipeline pump and pipeline booster pump, it is necessary to emphasize their respective concept definitions.　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.Los Angeles,　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time,Monte Cristo San FernandoHH slurry pump, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness,Monte Cristo San FernandoHorizontal non clogging sewage pump, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements,Monte Cristo San FernandoWear resistant slurry pump, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　The stemless submersible sewage pump products with early models and parameters are also the most commonly used submersible sewage pump products. It is WQ submersible sewage pump series. Since the impeller of this series of submersible sewage pump adopts the double blade impeller structure, it is not suitable for this series of submersible sewage pump to form a stem when transporting sewage　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.Product range, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　 Next, the water seal, lock ring and other parts need to be installed.

　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingranking,　　Commodity.　　Required lift (m)　　 Next, the water seal, lock ring and other parts need to be installed.Monte Cristo San Fernando,　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?