Sign in perhaps register 。

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.BassettLongitudinal welded pipe has the advantages of simple production process, high production efficiency low cost and rapid development. The strength of spiral welded pipe is generally higher than that of straight welded pipe. It can produce welded pipe with larger pipe diameter with narrow blank, and welded pipe with different pipe diameter with blank of the same width. However, compared with the straight seam pipe with the same length, the weld length increases by ~ , and the production speed is low. Welded pipes with large or thick diameter are generally made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be welded directly through steel strip. Then after simple polishing, wire drawing is OK. Welded pipe is welded with strip steel, so it is not as high as seamless pipe in its original position. Welded pipe process: uncoiling of raw materials - leveling - end shearing and welding - looper - forming - Welding - removal of internal and external weld beads - pre correction - induction heat treatment - sizing and straightening - eddy current testing - cutting - hydraulic inspection - Pickling - Inspection (strict control) - Packaging - delivery.Introduction to product knowledge of alloy pipe:Trujillo,Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, and reduce the construction cycle time of the project. On the whole unique and convenient installation, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Application characteristics of I-beam:I-beam is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing.

The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard. Spiral seam submerged arc welded steel pipe (SY- for pressure fluid transportation is a spiral seam steel pipe used for pressure fluid transportation, which takes hot-rolled steel strip coil as pipe blank, often warm spiral forming and welded by double-sided submerged arc welding. The steel pipe has strong pressure bearing capacity and good welding . After various strict scientific inspections and tests, it is safe and reliable to use. The steel pipe has large diameter and high transportation efficiency, and can save the investment in laying pipelines. It is mainly used for transporting oil and natural gas.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength,BassettGb5310 seamless pipe manufacturer, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.investment, Small longitudinal crackIn order to make the steel pipe workpiece have the required mechanical, physical and chemical properties in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint,Bassett16Mn large diameter longitudinal welded pipe, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.

Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Click to view,The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~,BassettIncoloy800H alloy pipe, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method. Quality requirementsAlloy pipes can be used for heating (cooling) projects.Bassett,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete