Sign in perhaps register 。

　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterGuadeloupe,GuadeloupePipeline pump,　　It is necessary to set up a protection system, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.Ancona,　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.

　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation,GuadeloupeSewage pump diving, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　There is no suction line. As the water storage tank is not deep enough and the suction pipe of the water pump is not deep enough, the inlet pipe of the water vortex is not deep enough. Water with a lot of gas. Destroy all normal water Self-priming pumps. To ensure sufficient depth of digestion and absorption of low watermark water. At that time, the depth was .~lm and it was impossible to　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is smallHow much does it cost?,　　 Inspection before installation: Check the specification, and pay attention to the temperature rise outside the packing chamber.　　For example, concentrate and tailings are treated in the concentrator,GuadeloupeCorrosive pipeline pump, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar % ore slurry %; It can be operated in series according to the needs of users.

　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.Product line, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canGuadeloupe,　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.