Sign in perhaps register 。

Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).The inspection items, sampling quantity, sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Martinique Island,Square tubes can be degreased with organic solvents (vinyl chloride, carbon chloride, industrial solvents, benzene, acetone, etc.), concentrated or alkaline solution. Industrial vinyl chloride is suitable for degreasing metal parts; Industrial chlorinated carbon is suitable for degreasing ferrous metal and non-metallic parts; Vinyl chloride is suitable for degreasing metal parts and non-ferrous metal parts; The industrial concentration shall not be less than %, which is suitable for manual scrubbing of the inner surface of the container with low degreasing requirements; % concentrated, suitable for degreasing some pipe fittings and porcelain rings of concentrated device.Generally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.Bergen op Zoom,According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.

Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.In order to ensure excellent coating quality, the coating is required to be firmly attached to the surface of the coated object. This depends on the quality of the coating itself; On the other hand, it depends on the quality of the coated surface treatment before construction. After various surface treatments, the coating quality and economic effect are very different.Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic metal ceramic and metal metal welding.Sincere service,Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Stage ( & mdash; )

Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.Focus on Development,The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.There are some defects in qb square tube during stretching, which are caused by the following reasons. The common main reasons are as follows: select the appropriate qb square tube material, and the commonly used materials in austenitic qb square tube are CrNiTi and CrNiTi. During deep drawing, CrNiTi is more stable than CrNiTi and has better crack resistance. Therefore, CrNiTi material should be selected as much as possible.Square tubes have different functions and different characteristics. Square tubes of various specifications, square rectangular tubes,Martinique IslandDN100 galvanized square pipe, seamless square tubes, galvanized square tubes and galvanized tubes are welcome to waste merchants,Martinique IslandPrice of galvanized square pipe equipment, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.Martinique IslandThe strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.The load of impact toughness acting on the parts at a great speed is called impact load. It is specialized in products and renewable resources. Its business includes: square tube, square tube, seamless square tube, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle,Martinique IslandHow much is a galvanized pipe, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.