Sign in perhaps register 。

Generally, chemical and electrolytic methods are usedGenerally, chemical and electrolytic methods are usedEscondido port,How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm (MPA). Upper yield pointFerrous metals refer to iron and iron alloys. Such as steel, pig iron, ferroalloy, cast iron, etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, collectively referred to as iron carbon alloy.Santa Rosa de CabalSquare tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.Square tube nonferrous metals, also known as non-ferrous metals, refer to metals and alloys other than ferrous metals, such as copper, tin, lead, zinc, aluminum, brass, bronze, chromium, nickel, manganese, molybdenum, cobalt square tube, vanadium,Escondido portGalvanized square pipe 40, titanium, etc. are also used in industry. These metals are mainly used as alloy additives to improve the performance of metals. Tungsten, square tube titanium, etc. are mostly used to produce cemented carbide for tools. The above non-ferrous metals are called industrial metals. In addition, there are precious metals: platinum, gold, silver and rare metals, including radioactive square tubes.The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, high price service, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.

The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Spray fluorocarbon paint after.The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.Respect for customers,Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system boiler and superheater. It is a long-term business square pipe,Escondido portProduction video of galvanized square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃ and the working temperature of alloy steel square pipe wall shall exceed ℃.Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam and its purpose is limited to general low pressure fluid.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.

Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Honest management,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap,Escondido portHot dip galvanized square pipe welding, resulting in uneven walking feeding.The inner and outer walls of the pipe shall retain the original surface without any processing.When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Escondido port,High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, plates and tubes. It is divided into cold rolling and hot rolling.