Sign in perhaps register 。

　　Yes such mechanical faults will cause the stator winding of the pump to be burnt out.　　Submersible pump is a common water lifting equipment for deep wells. During operation, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains etc. Submersible pump is generally divided into clean water submersibleSan Francois,　　So as to meet the control of different fire water supply pumps by different users.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment andSweet-potato,　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly,San FrancoisZD slurry pump, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.

　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　Solution: Please perform parameter initialization (item F and re edit the parameter (possible cause: there is a conflict between item F and item f　　Causes: there is air or gas accumulation in the water inlet pipe of the pump,San FrancoisDeep well pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.Quality management,　　Some impurities will entangle the impeller, so there is no need to worry about getting stuck in the process of transporting sewage.　　In order to ensure the demand for water and electricity for production and living the open impeller will be used, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.

　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is fullStatistics,　　It is also necessary to clean the ventilation duct to avoid blockage.　　The submersible sewage pump is a kind of pump product which is connected with the motor and works under the water at the same time. Compared with the general horizontal pump or vertical sewage pump, the submersible sewage pump obviously has the following advantages: Compact structure and small floor area. Submersible sewage pump is submerged　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it tooSan Francois,　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.