Sign in perhaps register 。

I have seen the evaluation video before. Netizens rub the steel ball of cleaning tableware back and forth on the SPC floor and there is no trace on the surface.If it&#;s a wooden floor, I think it&#;s not like it anymore. You can see how good its wear resistance is.The cross section of the floor is rubbed with a file, so that the heat generated in the cross section is the full volatilization of formaldehyde (formaldehyde will accelerate the release above ℃, and some irritating smell can be smelled). At this time, you can smell it. Generally, you can smell three different levels of smell:Mandeville, Environmental protectionFour look at the brandBaliban, compression resistance, impact resistance, fire resistance flame retardancy and chemical pollution resistance, in daily use, it only needs to be cleaned with a twisted dry rag, wipe it with a cloth stained with detergent.The water resistance is reflected by the water absorption thickness expansion index. If the index value is high, the water resistance is poor, that is, it is easy to cause size change in humid environment.Must not listen to the misleading such as waterproof floor, only moisture-proof floor, no waterproof wooden floor.

The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand,MandevilleWhat brand is good for waterproof, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush,MandevilleHow to lay wooden floor when the ground is uneven, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Ninth, laser cutting is simple and easy.The density of laminate floor substrate (high density fiberboard) shall be .-. g / cm, and it is not appropriate to have too low or too high density.quality,In addition, pay attention to whether there are sawdust and stratification on the cutting surface of the plate and whether there are sawdust and stratification on the cutting surface of the solid wood floor. Defects.Generally, the plate has a certain degree of expansion, so some gaps (.mm is appropriate) should be left between the laths during splicing to avoid arching.If the floor of the room is uneven, it can be paved with wooden keel for leveling, and then nailed with lath on it. After planing, paint and wax can make the room elegant, extraordinary, clean and warm.A short wooden floor strip has been launched in the market, which can be combined freely according to the size of the room, and can be assembled into a variety of patterns at will.This kind of short plank is more practical, but the disadvantage is that the cost is not low.If the floor is made of wood, the wallboard can also be decorated with plates, so that the overall structure of the room tends to be unified.Wall panels can be used as whole wall paneling or only as dado paneling.Wood wallboard is the best for large wallboard concrete wall. It can directly fix the board to the wall with adhesive.If the white ash interior wall of brickwork structure is decorated with wallboard, it shall be fixed for minutes first×mm vertical wood wall reinforcement, and then fix the plate to the wood wall reinforcement with wood screws.Family decorative wallboard is best based on plywood, and its strength is appropriate.Then stick wood veneer on its surface to make up for the deficiency of plywood pattern.After the veneer is pasted,MandevillePrice of multilayer composite wood floor, apply one or two layers of matte paint, and the pattern of the wallboard will be clear and beautiful, smooth and three-dimensional.Wood floor and wood wallboard interweave, making the style of the whole room unified, both simple and elegant.On the basis of uniform color or reasonable interweaving it can make the whole room comfortable and soft, and give people an indescribable sense of mystery.Introduction of floor leather

Fifth, the total thickness of the floor is about , cm which is also related to his total price.Where to sell API,High concentration formaldehyde is a genotoxic chemical.In animal experiments, high strength, no trace in daily application, and beautiful and generous. Green environmental protectionMandeville, Stable quality and not easy to damage: the solid wood composite floor plate adopts double plate composite type, and the wood chemical fiber is bent into a network structure and laminated. Various thermal stresses of wood are integrated into multiple plates to ensure the flatness and stability of the wood floor and preserve the beauty of the solid wood floorAs mentioned above, calcium powder has good thermal conductivity, so paving the floor at home is the best choice. Even if it gets hot, it will not release harmful gases.SPC floor is a new type of floor, also known as stone plastic floor. Its base material is a composite plate made of stone powder and thermoplastic polymer, which is stirred evenly and extruded at high temperature. At the same time, it has the characteristics of wood and plastic to ensure the strength and toughness of the floor. waterproof, PVC has no affinity with water, SPC flooring will not be deformed due to moisture, so it is a good choice for flooring.