Sign in perhaps register 。

　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way,　　Operation management of screw pump Nemo pump (single screw pump) is a positive displacement pump, which is widely used in sewage plant to transport sludge and chemicals containing solid particles.　　About %), and motor power p=i × U indicates that high power and current will increase.Abu Arish,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control the circulation in the slag slurry pool is basically unchanged　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　For example, concentrate and tailings are treated in the concentrator,MegikanosLong shaft submerged slurry pump, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, ore slurry %; It can be operated in series according to the needs of users.

　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　 Change the oil: if the oil contains water, drain it, change the oil, seal the gasket, and then tighten the screw plug.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Finance Department,　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.　　It will burn out. If there is a heating problem in use,MegikanosSelf priming non clogging sewage pump, you can refer to the following reasons.　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.

　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.Online consultation,MegikanosCorrosive pipeline pump,　　Rate loss, so shaft power = effective power + lost power.　　It can be divided into single slurry suction pump and double slurry suction pump; The second is that the slurry pumps can be classified according to the pump shaft and horizontal position of the slurry pump: horizontal slurry pump and vertical slurry pump. The horizontal slurry pumps of Panshi pump are mostly ah, AHR, HH and ZJ　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!Megikanos,　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion