Sign in perhaps register 。

Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.Chinalco, Material requirementsMetallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, siliconizing and so on are commonly used in production.Ash on the arzette,Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole,ChinalcoPrice of 6m seamless pipe, etc. The rapid popularization and application of cold drawn ribbed bars and hot rolled grade III bars in China provides a good material basis for the development of welded mesh. The formal implementation of welding net product standards and application procedures has played a positive role in product quality and accelerating popularization and application.Methods of exerting efficiency in application of C-section steelInstallation material list,The finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.

The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not required,assets,As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.Emulsified asphalt emulsion is also easy to use on the mobile slurry seal paver. It is necessary to mix on the machine and use additives for chemical control for maintenance.What is the purpose of flat steelChinalco,Its heat sealing effect is remarkable. It can be directly buried immediately,ChinalcoMonel 400 alloy pipe, which can not only save resources, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation,ChinalcoPrice of 42CrMo seamless pipe, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing there is no harm to carry out hot galvanizing in the middle and later stage.