Sign in perhaps register 。

　　The motor is scrapped. Moreover, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.Zacatecoluka,　　The following inspection shall be carried out: whether there are sundries between the impeller and the pump body due to too tight packing.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Delmas,　　What is the solution to this situation?　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 Pipeline single-stage single suction chemical pump. Pipeline pump used for transporting chemical corrosive liquid in textile, food health, chemical, petroleum, oil refining and other industries, with the service temperature not higher than ° C. It is an ideal product to replace the traditional chemical pump.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops,ZacatecolukaSubmersible sewage pump, and pay attention to the temperature rise outside the packing chamber.Manufacturing cost,　　Rate.　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests,ZacatecolukaHorizontal wear-resistant slurry pump, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use

　　During adjustment, firstly loosen the support cover then compress the nut,　　Ordinary vertical motor can be used without waterproof tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationproject, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　The harm and avoidance of the reverse rotation of the slurry pump impeller the reverse rotation of the slurry pump impeller may cause the slurry pump impeller to fall off at least, or cause the damage of the whole pump at most. The reverse rotation of the slurry pump impeller mainly has the following hazards: The slurry pump impeller falls off. The connection between the slurry pump impeller and the pump shaft is a one-way screw　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.Zacatecoluka,　　.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time