Sign in perhaps register 。

When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.The principle is similar to that of the plate rolling machine. The bending machine can determine a circle. Adjust the height to adjust the curvature.Lower Vega,Square tubes shall be stored with supports, products and tens of millions of products for you to choose. Professional square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe and secure. They shall be at a certain distance from the ground to ensure the ventilation of square tubes.If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed),Lower VegaGalvanized square tube customization, the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times) and propose acceptance with a new batch.Larkana,For gas transmission: gas, steam and liquefied petroleum gas.For structure: as pile driving pipe and bridge; pipe for wharf, road and building structure, marine pile driving pipe, etc.It is the process of drawing the die hole of the rolled metal blank (shape, pipe product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.

Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Spiral square pipe for low-pressure transmission (standard of the Ministry of petroleum), with the standard number of syt-. The representative material is qbqb and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, natural gas, heating and other pipelines.Fatigue strength, plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Interpretation and observation,The inspection items, sampling quantity sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar core pipe, casing, sedimentation pipe, etc.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.

The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening,Lower VegaProduction of hot dip galvanized square pipe, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Quality inspection report,Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.After perforation, the round tube blank is successively rolled by cross rolling, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening, the steel pipe is taken by the beltQB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, etc; Low alloy steels are divided into q Mn, Q, St-, etc.Lower Vega,Square tube, modified square tube, square tube,Lower VegaGalvanized square pipe schedule, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, such as arc, electric spark, flame, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.