Sign in perhaps register 。

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Henan,Conscientiously write the special construction plan for installation and construction, and make technical disclosures to the installers.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Keren,The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Boarding bridges are divided into mobile boarding bridges andBrief introduction of application range and mobile boarding bridge: high-priced elevator factory of various specifications welcomes waste dealers, industrial companies, enterprises, and power departments to visit and negotiate with the company! It is used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, the mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a mobile steel-structured slope, and the forklift can also directly drive into the truck compartment for batch loading and unloading operations. . Quick loading and unloading of goods can be realized with only one person operation and no power supply required.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different rated loads and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, table size mm *mm, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Credit guarantee,Prepare the foundation according to the foundation plan, leveling, and alignment to ensure the level of the foundation and various requirements for use.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found,HenanFixed lifting cargo elevator, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean and the travel switch points of each safety device must be safe and reliable.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.

What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.supply,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Just like the failure of the walking part of the lifting platform, the operator must master the common sense of equipment maintenance and failure, so that he will not appear too flustered when a failure occurs. Generally speaking, the common faults of the walking parts of the lifting platform are divided into: bearing pad burning axle box bearing burning, traction motor bearing burning, wheel tire relaxation, collapse and other fault problems. Below, I will share with you the solution.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Henan,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition,Henan5 ton lifting cargo elevator, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof),HenanA cargo elevator needs to, with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.