Sign in perhaps register 。

　　Submersible slurry pump In addition it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professionalAwachapan,　　Submersible slurry pump is an important equipment in drilling and water intake operations. When the equipment is working, it is submerged as a whole. Pumping groundwater to the surface is widely used for domestic water, mine emergency rescue,AwachapanWQ submersible pump parameters, industrial cooling, farmland irrigation, geothermal heating in residential areas, etc. You will be briefed on it Scope of application.　　During adjustment, firstly loosen the support cover, then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationSolrod Strand,　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer,AwachapanTwo stage slurry pump, and dry it naturally.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.

　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　The pipeline support is unstable and shakes.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Safety and health,AwachapanSewage pump diving,　　It is located in the middle, so it seems that many regions have good effects when using it.　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　Potential energy pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?

　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.consumption,　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　When assembling the motor and water pump departments below grade , firstly, tighten the nuts evenly between the water inlet joint and the contact plane from the upper part to the bearing seat, pump shaft, fixed studs and lock rings, and install the guide housing and impeller　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceedsAwachapan,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane