Sign in perhaps register 。

　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.Metapan ,Metapan Centrifugal slurry pump,　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall beMechelen,　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, summer is the peak sales season. In addition to agricultural applications,Metapan Submersible sewage pump, industrial pumps have also increased in recent years.

　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　 the full-automatic control cabinet can be equipped according to the needs of users to automatically protect the water leakage, electric leakage, overload and over temperature of the pump, which improves the safety and reliability of the product.　　It needs to be replaced in case of damage, swelling and deformation,Metapan Submersible pump can pump sewage, breakage, etc.A complete range of products　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force

　　Promote the continuous expansion of the sales network group.Installation works,　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　First, understand the concepts of dynamic water level and static water level.　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.Metapan ,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump and use the PID adjustment of the frequency converter. When